I am using nucleo-wb55 development board with STM32WB55 processor. I want to connect sensors like IIS3DWB, STTS22H to this board. How can I go about connecting the modules of these sensors to nucleo-wb55?
stm32wb, nucleo-wb55, sensor, hardware
214 Views Asked by AliEkber At
1
There are 1 best solutions below
Related Questions in STM32
- STM32F303VC : device not found
- Very few write cycles in stm32f4
- Put a bootloader program at the bottom of the FLASH memory
- STM32 USB HID reports
- STM32 flashing disabled after flashing a code without R/W protection
- How can I align stack to the end of SRAM?
- STM32 I-CODE and D-CODE buses
- how to use arm-none-eabi-gcc compile STM32 program
- Write a custom bootloader with the STM32L1 series in C
- What are the steps to setup an RTOS application on STM32 using Linux and Makefiles instead of using Windows based IDEs?
- Loosing some bytes on USART transmission with STM32L1XX
- my bootloader doesn't boot my new program on stm32
- Using printf causes error
- Estimating available RAM left with safety margin in C (STM32F4)
- Flashing image to STM3220g-EVAL board using Trace 32
Related Questions in SENSORS
- Get GPU temperature in Android
- Proximity sensor in Swift (from Objective-C)
- How to get temperature value from DS18B20 voltage
- Receiving sensor events in worker thread (Android native)
- How can I unrigerster the listener to read event every 5 seconds
- Calculating the pulse rate using sensors
- What does SampleRate.MS16, MS32, MS128 stand for when associated with sensor listeners?
- How does the android OS determine a SensorEvent's accuracy?
- HID Temperature Device Report Reading
- Activate proximity sensor on button click
- How can i build /hardware/libhardware/tests/nusensor?
- How to connect two sensors into Raspberry Pi?
- Scaling Movieclip according to the input from sensor
- how to code if statement when using a sensor
- How to calculate the orientation of a IMU sensor?
Related Questions in NUCLEO
- Error launching openOCD debugger in Eclipse
- Getting continuous stream from Lepton FLIR Camera with board Nucleo-f401re
- Nucleo F401RE - Interrupt not working
- How to do a adc conversion every 1us with Nucleo-F303K8?
- Does fmodf() cause a hardfault in stm32?
- Why HAL slow down the UART transmission.?
- Came up with an "Unable to stat debugging" error when Debug program for STM32 NUCLEOF103RB
- Can't get TransmitReceive to work on STM32 nucleo board
- Assertion error while trying to debug program STM32CubeIDE, using NUCLEO board: exit error 3
- STM32F446RE Nucleo LD1 slow blinking red and I'm not sure why
- Is it possible to configure a CAN transceiver with an FDCAN microcontroller?
- STM32F103RB - How to know what pin to use to send a trigger signal
- STM32 CPU Usage during ISR
- Accessing external storage on Nucleo
- STM32 I2C interrupt method requires a blocking while loop?
Related Questions in HARDWARE-DESIGN
- Unknown Wrong result when simulating Verilog design in modelsim
- Using Generate in Vhdl
- How to implement a schematic in vhdl code and converting the datatypes from std_logic to bit
- Why are inner components not being executed
- Can I use openCV libraries with Catapult C?
- Verilog: wait for module logic evaluation in an always block
- Can two chips take turns accessing two memory banks?
- stm32wb, nucleo-wb55, sensor, hardware
- Multiplexer in vhdl with structural design
- Cache request in Forth CPU
- Hardware for "A div B" with A and B fixed point
- Xilinx iterate error: Loop has iterated 64 times. Use "set -loop_iteration_limit XX" to iterate more
- Hardware design a 3 binary numbers adder
- How to manage uninitialized input signals
- Data hazards in hardware platforms
Trending Questions
- UIImageView Frame Doesn't Reflect Constraints
- Is it possible to use adb commands to click on a view by finding its ID?
- How to create a new web character symbol recognizable by html/javascript?
- Why isn't my CSS3 animation smooth in Google Chrome (but very smooth on other browsers)?
- Heap Gives Page Fault
- Connect ffmpeg to Visual Studio 2008
- Both Object- and ValueAnimator jumps when Duration is set above API LvL 24
- How to avoid default initialization of objects in std::vector?
- second argument of the command line arguments in a format other than char** argv or char* argv[]
- How to improve efficiency of algorithm which generates next lexicographic permutation?
- Navigating to the another actvity app getting crash in android
- How to read the particular message format in android and store in sqlite database?
- Resetting inventory status after order is cancelled
- Efficiently compute powers of X in SSE/AVX
- Insert into an external database using ajax and php : POST 500 (Internal Server Error)
Popular Questions
- How do I undo the most recent local commits in Git?
- How can I remove a specific item from an array in JavaScript?
- How do I delete a Git branch locally and remotely?
- Find all files containing a specific text (string) on Linux?
- How do I revert a Git repository to a previous commit?
- How do I create an HTML button that acts like a link?
- How do I check out a remote Git branch?
- How do I force "git pull" to overwrite local files?
- How do I list all files of a directory?
- How to check whether a string contains a substring in JavaScript?
- How do I redirect to another webpage?
- How can I iterate over rows in a Pandas DataFrame?
- How do I convert a String to an int in Java?
- Does Python have a string 'contains' substring method?
- How do I check if a string contains a specific word?
You can connect them via the I2C and SPI interfaces the board provides. Either built your own I2C/SPI or use the STM32 HAL provided functions.